Lexmark Laser Error Codes

Lexmark error codes may not apply equally to all models. How did we do? Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Remove toner cartridge for better access to jammed paper.   Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input sensor as made.   ERROR 22 The exit sensor was not unmade in time.   ERROR 23 Jam at the duplex unit. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. See “Duplex” on page 2-16   Error 24 The defined paper size is too short to print data as formatted.   Error 25 Input sensor made at wrong time. May be due to the paper feeding manually while motors running and previous page in path.   Error 26 Duplex unit is installed but paper tray is not sensed.   Error 27 Envelopes/paper loaded are wrong size.  Load correct size Error 28 Input sensor not made after pick attempt. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed.   Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.   Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on the print cartridge as the cover closes. The pin should enter the tower on the HVPS and depress the cover switch.   Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. It may take the printer 10-20 seconds to determine if the print cartridge is defective. Remove and reinstall print cartridge. Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer.   Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job.   Error 38 38 Memory Full Memory used to store pages is full. To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Make sure the memory shown on the printout matches the installed memory.   Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Make sure the memory shown on the printout matches the installed memory.   Error 43 Font card format not supported by printer.   Error 44 Defective font card installed in font slot.   Error 47 47 Font Card Removed While Printing Printer needs data on removed card.   Error 52 Flash Full - Not enough flash memory for data requested to be stored.   Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write.   Error 54 Serial Error - Framing or parity error on serial.   Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed.   Error 59 Duplex Cover Open Top cover of duplex unit is sensed open.   Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk.   Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. Run the Quick Disk Test. If the test fails, the disk is defective or the data on track1 is bad. If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. test). Replace the disk if instructed by the operator panel.   Error 7X Network Card Codes These user codes are documented in various network card user manuals. See “Network Wrap Tests” on page 23.   Error 80 Network Card Codes These user codes are documented in various network card user manuals. See “Network Wrap Tests” on page 23.   Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.   Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced. Press "GO" to clear message and temporarily continue   Install OPC Belt/Photo Developer Error 84 Transfer Drum Exhausted The Transfer drum has reached the end of it's life and must be replaced.  May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner.   Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Unit. Remove the duplex front cover to access the jam area. If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer. Open the printer rear door to access the jam.   Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. Remove jammed media Error 90X Software Error Unrecoverable software error. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace the system board. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again.   Error 901 Engine Flash Indicates the Flash with the system code program is defective   Replace System Board Request Quote Error 914 DC Pick Motor - No Encoder Feedback Check the integrated paper tray, tray 1, for paper loading problems. Reload the paper and do a power on reset. Check connecting cables for continuity. If cables, connectors and connections are good replace assemblies listed. Replace the Autocompensator Assy. Replace System Board Request Quote Error 917 Transfer Roll Error Cannot start servo operation. Verify correct cable connections from the Engine board to the HVPS. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact.   Error 920 920 Fuser Error Fuser is below temperature while printing. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Error 920.X and 922.XX may display for a cold fuser. Some 920.xx error codes may be cleared by turning the printer on and off and allowing it to complete POR. Some 920.xx error codes may be cleared by turning the printer on and off and allowing it to complete POR. Fuser errors can be from a cold fuser or an overheated fuser. Newer machines display a sub code to indicate which condition applies. Error 921 Fuser is below standby temperature when idle.   Error 922 Fuser failed to reach standby temperature. Check the continuity of the fuser lamp at the two heavy leads. If an open circuit, replace the lamp or fuser. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms            Replace fuser assembly Shop For:   Lexmark       Maintenance Kits Lexmark Fusers Error 923 Fuser is too hot while printing or when idle. Lexmark Fusers Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Lexmark Fusers Error 925 Wrong fuser lamp installed. Check the fuser lamp for the correct type of lamp that should be installed. • Verify the line voltage is not exceeding the maximum rating for the printer. Lexmark Lamps Error 927 Main Fan Stalled or Cartridge Fan stalled, Check fan for binding or defective bearing - Replace Fan Error 928 Erase lamp assembly missing or disconnected   Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is defective.   Error 931 Printhead error - No first sync   Error 932 Lost hsync Replace Printhead Error 934 Printhhead Error - Lost Lock condition Replace Printhead Error 935 Printhead Error - Mirror motor unable to reach operational speed Check cables, look for chafing or damage to ribbon cable at sharp bends around rear cover. Replace printhead or ribbon cable. Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra s 1250 Optra s 1650 Optra s 2455 Optra s 1255 Optra s 1855 Optra s 2420 Optra s 1620 Optra S 1625 Optra Se 3455 Optra t610 Optra t612 Optra t614 Optra t616 t520 t522 t620 t622 t630 t632 t634 Optra T 640/642/644 Mirror motor not up to speed. Check printhead, cable, motor, system board. Power printer off one to two minutes. Open doors and covers and remove the toner cartridge. Make sure there is no paper jammed in the printer. Pay close attention to the area where the toner cartridge sits. The main motor is located just to the left of the toner cartridge. If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service. The main motor assembly may need to be replaced. Error 939 RIP Communications Lost Controller EngineCommunications Lost The controller board and the engine board cannot communicate with one another. POR several times Check each board for secure ground. Replace the assys in the following order 1. Controller Bd 2. Engine Board 3. Intterconnect     Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle (TMC) is where the code and electronics in the printer sense an addition of toner in the cartridge developing area. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed.            Check the toner metering cam on back of suspect cartridge. If not present check in printer. Replace defective cartridge. Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. Check connections to the to interconnect card assembly. Check AC power source for noise. Replace low voltage power supply assembly. Request Quote 953-954 NVRAM Failure NVRAM Failure  953: NVRAM Chip Failure                         954: NVRAM CRC Failure Optra T 640/642/644 953 - Replace the operator panel board or upper front cover. 954 - Replace the interconnect card. Replace System Board Request Quote 980-984 Service Errors Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin.

back to top How did we do?